Choose your delivery country
Ships today when ordered before 15:00 CETShips today when ordered before 15:00 CET
Wisman Group
Sale20% off all cable carriersAll through September — the discount is already included in the prices.

Uniflex Advanced Series — Tsubaki Kabelschlepp

Uniflex Advanced Series by Tsubaki Kabelschlepp: the complete plastic cable carriers series, available from stock.

All 314 articles of the Uniflex Advanced Series are listed below with full technical data. This plastic cable carriers series can be ordered online; inner height 17.5–44 mm, inner width 25–250 mm, bend radius 28–1250 mm. Not sure about the right size or bend radius? Our engineers are happy to calculate your application.

314 articles in this seriesAll plastic cable carriers

  • Ordered before 15:00, shipped the same day
  • Datasheet and STEP file with every article
  • Technical advice from a design engineer

About the Uniflex Advanced series

The all-rounder from Tsubaki Kabelschlepp: the widest dimensional range, hinged on both the inner and outer radius.

The Uniflex Advanced series is the most popular plastic cable carrier in our range, and for good reason: with inner heights from 17.5 to 44 mm and inner widths up to 250 mm, a single series covers the vast majority of machine building applications. The links feature a double stop system, ensuring the carrier remains rigid even over longer unsupported lengths while keeping noise levels low.

Every size is available with hinged crossbars on the inner or outer radius, allowing cables to be added later without dismantling the carrier. Dividers, end connectors and strain relief from the same series fit seamlessly without modifications.

Key strengths

  • Largest selection of inner dimensions and bend radii within a single series
  • Hinged crossbars on inner or outer radius, per link
  • Double stop system for rigid, quiet operation
  • Complete range of accessories: dividers, end connectors, strain relief

Typical applications

  • General machine building and gantry systems
  • Packaging and handling machines
  • Linear axes with medium travel lengths
  • Retrofit applications where cables will be added later

Configurator

Cable chain configurator

Send us your cable list and we will calculate everything for you.

Calculate my cable chain

Can't find your cable carrier?

No problem — we're happy to prepare a tailored quote, including complete systems and special versions.

Request a tailored quote

314 articles

All about plastic cable carriers

Technical guidance from our engineers: how to choose, what to measure and where installations fail in practice.

How to determine the right inner dimensions

Lay out every cable and hose that has to travel and add up the outer diameters. Add 10% clearance: that is your minimum inner width. The thickest cable determines the inner height, because a cable must never be pinched between the crossbars. With multiple layers, stay below 60% fill ratio or friction — and therefore wear — rises quickly. If you are between two sizes, choose the larger one: an extra separator is cheaper than a second carrier.

Bend radius, travel and unsupported length

The bend radius should be at least ten times the diameter of the thickest cable — often twelve to fifteen times for shielded or heavy power cables. The travel determines the chain length: roughly half the travel plus the bend plus a small reserve. Beyond a series' unsupported length the carrier will sag; then pick a heavier series or let the upper run glide on the lower run in a guide trough.

Open or enclosed design

An open design with crossbars ventilates better and is easier to fill; choose it in clean environments and for warm power cables. An enclosed design (cover bands or tubes) keeps swarf, dust, coolant and sparks out and protects wiring on machine tools, laser cells and welding robots. Both are available openable — inside, outside or on both sides — so maintenance does not require dismantling the whole carrier.

Installation and maintenance

Install cables de-energised and without torsion, never twisted, and clamp them only at the end connectors with strain relief. Distribute heavy cables symmetrically across the width and separate power from signal with separators. At the first service, check the chain hook, the bolted joints and the sliding surfaces; audible wear or dust almost always means the bend radius is too small or the fill ratio too high.

Frequently asked questions

The questions our technical desk receives most often about this category.

When should I choose Uniflex Advanced instead of a smaller series like QuickTrax or MONO?

As soon as you need to lay more than a few cables, require an inner height above approx. 17 mm, or bridge an unsupported length of more than one metre. Uniflex Advanced is more rigid and offers a wider choice of width, bend radius and internal separation.

Can I add cables once the Uniflex Advanced is already installed?

Yes. The crossbars open per link on the inner or outer radius, depending on the selected version. You do not need to disconnect the carrier to add or replace a cable.

Which dividers fit this series?

Dividers and shelves from the Uniflex Advanced series snap into the crossbars without tools. We recommend a separate compartment for each cable or hose; the configurator calculates the number of compartments for you.

How do I choose the right size of plastic cable carriers?

Start with the fill: the thickest cable sets the minimum inner height, the sum of all diameters plus 10% clearance sets the inner width. Then pick a bend radius of at least ten times the thickest cable diameter. Filter on those three values on the left and only suitable articles remain.

What is the lead time and when do you ship?

Articles marked 'in stock' ship the same working day when ordered before 15:00 CET. Articles 'on request' are made to order at the manufacturer; the lead time is stated in the quotation, typically 5 to 15 working days.

Do I get technical documentation and CAD files?

Yes. Every article lists a datasheet, a manual and a STEP file for your 3D model. All are free to download, no account required.

Are the prices volume prices?

The price shown is per unit. From the indicated tier quantity onwards the lower price applies automatically and is calculated in the cart. Use the toggle at the top to show prices including or excluding VAT.

How many metres of carrier do I need for my travel?

Rule of thumb: half the travel + the bend (π × bend radius) + roughly 200 mm reserve for the end connectors. With a 6 m travel and a 150 mm bend radius that gives about 3000 + 470 + 200 = 3.7 m. For hanging or vertical installations we are happy to calculate it for you.

Can I extend or repair an existing carrier?

Yes, as long as you use the same series and inner width. Individual links, crossbars and separators can be reordered per series. Series name no longer legible? Send a photo of one link plus the inner dimensions and we will identify the series.

What fill ratio is still acceptable?

Keep at most 60% of the inner cross-section filled and leave at least 10% clearance per cable in its chamber. Fuller carriers run heavier, hotter and louder, and jacket wear increases sharply.

Didn't find what you were looking for?

We'll prepare a tailored quote. Fill in the quote form and you'll receive a matching quote by email within 3 hours on working days.

Request a quote

Also known as

These products go by several names in the market. If you searched for any of these terms, you are in the right place:

  • cable carrier
  • energy chain
  • cable chain
  • plastic cable carrier
  • cable track
  • cable guide chain
  • cable drag chain carrier